Colonna's Shipyard is looking to obtain experienced candidates within our Structural Department.
We are pleased to accept resumes for Pipe fitters.
This is a full-time position with competitive pay, based on experience, and immediate work within our headquarters in Norfolk, VA.
• Weld together metal components of products, as specified by layout, blueprints, diagram, work order, welding procedures, or oral instructions, using electric arc-welding equipment
• Select and execute best method to prepare all material surfaces to be welded, ensuring that there is no loose or thick scale, slag, rust, moisture, grease, or other foreign matter and to clean, degrease, deoxidize, or desmut weld joint or work piece, using wire brush, portable grinder, or solvent clean/chemical bath
• Weld completion in flat, horizontal, vertical, or overhead positions for at least three base materials using a wide variety of processes. (That is, deposit weld beads exhibiting proper sidewall and interpass fusion, size, profile, interpass cleanliness, wrap and staggered, fused, and cleaned starts and stops rarely (no more than 3%) requiring grinding/dressing to meet VT acceptance standards)
• Lay out work from blueprints for the following, but not limited to:
• Plates for shearing, burning by manual or automatic burning and cutting,
• Angles for punching and shearing, Drilling patterns, Templates for shaping steel, Plates and shapes to be shaped with or without heat, Stiffeners and bulkheads to plates, Bolt and fastener patterns for various parts, manholes, and equipment foundations
• Inspect work for proper fit-up and adequate cleanliness for welding; locate materials, fabricate and install from blueprints the following, but not limited to:
• Ladders, handrails. Stairways, grating, walkways Manholes and equipment foundations, Pipe racks and brackets, Pipe systems, Braces and supports to maintain straightness
• Fabricate the following, but not limited to:
• Fit brackets, panels, complex beam/shape structures
• Plumb transverse bulkheads and panels to fabricate enclosure Complex weldments, Shapes and plates, Simple and complex parts from a drawing or sketch
• Operate and set up of the following equipment, but not limited to:
• Hydraulic jacks and pumps, Chain falls, Come-alongs, Steamboat ratchets, Slings,
• Tie downs, Iron workers, Saws, Pneumatic and electric tools, Drill press, Pipe benders, Press brakes, Plate shears, Plasma cutting torches, All manual, semi-automatic, & automatic cutting torches & machines
• Expertly repair base metal products and completed welds by adding the minimum amount of weld metal or heat and the minimum amount of grinding/smoothing to meet job specification
• Perform multi-pass, all position fillet and groove welds using SMAW (Shielded Metal Arc Welding), GMAW (Gas Metal Arc Welding), Submerged Arc Welding, FCAW (Flux Cored Arc Welding) processes, or the most efficient combination thereof for steels, stainless steels or nickel-based alloys, and for copper-based alloys, aluminum alloys, or titanium alloys
• Also perform air-arc back gouging and oxy-acetylene torching (e.g. brazing, cutting, or pre-heating), GTAW (Gas Tungsten Arc Welding), and pipe welding, pipe flange and socket welding; as well as qualify to perform either flux cored inner shield welding, weld overlay cladding, automated back gouging, plasma back gouging or any combination thereof.
• Mark or tag material with proper job number, piece marks, and other identifying marks as required and always mark completed welds with welder number
• Perform single pass 5/16-inch minimum fillet welds in all positions using FCAW on carbon steel and at least ¼-inch single-pass fillets on two other materials
• Supervise set up to perform welding in accordance with applicable WPS all welding equipment such as: wire feeders, Sub-arc tractors, Bug O's, Power sources, etc.
• Clean torches and connect/lay-out cables and whips to optimize performance and perform routine maintenance on all equipment.
• Recommend WPSs and WPS upgrades required for a job; when assigned, produces or supervises production, documentation, and testing of PQRs and WPQs
• Reliable, leads by example; trains less-killed welders, enforces good workmanship and safe welding practices throughout the work area; identifies gaps in weld process controls and weld process surveillance inspections and recommends corrective action
• Perform comprehensive workmanship inspection, and when directed those of others, of all welds grinding and joint preparation for NDT processes as applicable; observe QA/NDT hold points as applicable
• Complete standard dimensional computations/ Devise bracing and weld sequencing steps to maintain tolerances and minimizing distortions
• Other duties as assigned
REASONABLE ACCOMMODATIONS STATEMENT
To perform this job successfully, an individual must be able to perform each essential job duty satisfactorily without posing a direct threat to the safety or health of employee or others. Reasonable accommodations may be made to enable qualified individuals with disabilities to perform essential job functions. The Company is prepared to modify or adjust the job or work environment to make reasonable accommodations to the known physical or mental limitations of the employee, unless the accommodation will impose an undue hardship. If a reasonable accommodation is needed, please contact the Human Resources department at (757) 545-2414.
Employees are exposed to moderate or high noise levels, saw dust, fumes, and hazards. Work at job sites exposes employee to weather conditions and the hazards of working on and around scaffolds and ladders. Employees may be required to work in confined areas which may be dusty and dirty. Protective devices such as but not limited to ear plugs, safety glasses, respirators, gloves, hard hat, and safety shoes are required.
Participate and promote a Safe Operations culture. Wear Personal Protective Equipment (PPE) per company guidelines at all times with no exceptions correcting others who are not in compliance. Learn and practice all safety requirement and procedures for any equipment or tools assigned to your trade. Participate in the planning of safe work and all housekeeping/cleanup activities. Be aware of and speak up about any safety issues that conflict with Safe Operations culture of Colonna’s Shipyard, Inc. Report or correct any safety concerns immediately.
It is every CSI employee’s responsibility to maintain cleanliness during all operations regardless of location, assignment, or department. The job or task is not complete until all materials, residuals, tools, and anything else is either stored correctly or removed from the workspace appropriately. It is Colonna’s commitment to ensure our work areas, often our customers vessels, and our facility are continually free of trash/debris and reusable materials are kept organized. A clean environment exemplifies pride in our work, respect for the next person who enters and our customers, and promotes an overall safe place of employment.
• Minimum of five years commercial/naval experience.
• Must be certified and documented to perform multi-pass, all position fillet and butt welds using the SMAW (Shielded metal arc) process.
• Ability to fuse inserts and weld carbon steel, stainless steel and copper nickel pipe using the SMAW and GTAW (Gas Tungsten Arc Welding) processes.
• Heating –Oxygen/Propane Heating Torch
• Experience working in physically demanding environments (shipboard, sub-assemblies, ladders, staging, etc.)
• Familiarity with OSHA regulations relative to the shipbuilding industry.
• Ability to properly use fillet gauges, butt gauges, and a six-inch scale.
• All positions using the SMAW and GTAW processes.
• Thin wall sockets (required for below 0.187 wall joints).
• Must be certified and documented to perform multi-pass, all position fillet and butt welds using SMAW (Shielded Metal Arc Welding), Gas Tungsten Arc (GTAW), GMAW (Gas Metal Arc Welding), FCAW (Flux Cored Arc Welding), for steel, stainless steel or nickel-based alloys, and for either aluminum alloys, copper-based alloys, or titanium alloys
• Comprehensive, broad, and current knowledge of welding techniques, tools and equipment
• Technical training or higher degree (preferred) and Minimum of 7 years of career experience in Welding OR IO years welding experience, 7 within the past ten years.
• Expert knowledge of and ability to use hand tools and instruments associated with the trade
• Must be able to work effectively with others; training experience preferred
• Proficient reading all types of blueprints and weld symbols, drawing dimensions/ tolerances, complex shapes and weld joints; build plans, sequencing, welding tools, jigs & fixtures, platforms/staging and work instructions to control distortion and improve quality-adjusted productivity
• Enter and move through manholes, climb ladders, or both to reach and work inside confined spaces
• Hands on experience with heavy metal steel welding procedures in all positions
• Basic mechanical knowledge and skills
• Mirror welding/restricted access experience
• Must be a steady, reliable worker and exemplary craftsman
• Must be able to comprehend and follow instructions and give instructions
• Experienced with performing visual inspections of welds and fit-ups
• Familiar with different forms of weld NDT and how specified NDT impacts selection and execution of weld processes
• Must pass J-1 vision test and respirator fit test
Position compensation is based on experience.
Our benefits include:
• Medical, Dental and Vision Insurance
• 401K, company match
• Paid Time Off (PTO)
• Legal Services
• Annual performance evaluations
• On-site Human Resources
• On-site gym
• Free and close proximity parking
• Employee perks/gifts and more
All resumes are reviewed immediately for consideration.
Colonna’s Shipyard and our affiliates are pleased to be an Equal Opportunity Employer.
EOE / M / F / DISABILITY / VET
These are our VALUES and the guidelines that make us a leader in our industry. We are pleased and confident in stating that our skilled employees are among the most respected experts in the ship repair industry.